車庫門頻繁的進行使用，車庫的卷簾門也就增加了出現問題的可能性，那么車庫門壞了換舊的行嗎？下面濟南卷簾門廠為您進行解答。

The garage door is frequently used, and the rolling shutter door of the garage also increases the possibility of problems. Is it OK to replace the broken garage door? Now Jinan Rolling Door Factory will give you an answer.

可以，查看現場應具備了裝置的必要條件，如已經通電，洞口平坦、規一。復核門洞尺度應與工程備料單上的洞口尺度、現場條件一致，假如原尺度丈量過錯或現場條件勘測，應及時向公司反響。

Yes, the site should have the necessary conditions for the device, such as power on, flat hole, and gauge one. The rechecked door opening dimension shall be consistent with the opening dimension and site conditions on the project material preparation sheet. If the original dimension measurement is wrong or the site conditions are surveyed, the company shall be informed in a timely manner.

1、先在需求裝置的門框框口方位畫出線，標明尺度巨細，然后找工作人員設計出適宜的車庫門（這兒值得留意的一點是框內高度比門扇的高度要高一點點）。

1. Draw a line at the door frame opening of the required device to indicate the size, and then ask the staff to design a suitable garage door (it is worth noting that the height inside the frame is a little higher than the height of the door leaf).

2、把車庫門的門框固定，這兒要先拆掉門框下部的固定板（留意：洞口兩邊地上要預留凹槽，經校對合格后，固定木楔，門框鐵腳與預埋鐵板件焊牢。

2. Fix the door frame of the garage door. First remove the fixing plate at the lower part of the door frame (note: grooves shall be reserved on the ground on both sides of the hole. After checking, fix the wooden wedge, and weld the iron foot of the door frame with the embedded iron plate.

3、裝置車庫門扇主體門扇。一定要確保車庫門與墻體結成全體，封閉性要做好，再粉刷洞口及墻體。粉刷結束后，門縫應均勻平坦，敞開車庫門應當自由簡便，不得有過緊、過松和反彈景象。

3. Install the main door leaf of garage door leaf. Make sure that the garage door and the wall form a whole, and make sure that the closure is good, and then paint the hole and wall. After painting, the door seam should be even and flat, and the garage door should be free and easy to open, without too tight, too loose and rebound.

此外使用期間要檢查車庫內部的金屬軌道。查看將軌道固定到墻壁的安裝支架。如果支架松了，請擰緊螺栓或螺釘。將車庫門關上，在車庫內部檢查軌道是否有凹陷、彎曲或變平的地方。如果有任何損壞之處，請用橡皮錘，或用一塊廢木料墊著錘子敲打這些地方。如果軌道嚴重?fù)p壞，您須更換。

In addition, check the metal rails inside the garage during use. Look at the mounting bracket that secures the rail to the wall. If the bracket is loose, tighten the bolts or screws. Close the garage door and check the tracks inside the garage for dents, bends or flattening. If there is any damage, please use a rubber hammer or use a piece of waste wood to cushion the hammer to hit these places. If the track is seriously damaged, you must replace it.

車庫卷簾門出現損壞的情況是一定要進行及時補救的，因?yàn)閱栴}發生后是會為自己先帶去不便，這一種現象也是比較麻煩的的，所以也要在這以前做好預防措施。更多相關內容就來我們網站http://m.ifxf.cn/進行咨詢吧！

Damage to the garage roller shutter must be remedied in a timely manner, because the problem will cause inconvenience for you after it happens. This phenomenon is also troublesome, so preventive measures should be taken before it happens. More relevant content will come to our websitehttp://m.ifxf.cn/ Consult!