電動卷簾門是一種安裝在許多公共場所的門，廣泛應用于各種商店立面的裝飾。安裝時應有專門的施工人員根據現場實際情況進行安裝調試。今天濟南卷簾門廠家來給大家說一下電動卷簾門在安裝時要注意幾個要點。

Electric roller shutter door is a kind of door installed in many public places and widely used in the decoration of various store facades. During the installation, special construction personnel shall carry out the installation and commissioning according to the actual situation on the site. Today, Jinan roller shutter door manufacturer will tell you a few key points to pay attention to when installing the electric roller shutter door.

（1）按設計型號，查閱產品說明書，檢查產品表面處理和零附件。

(1) According to the design model, consult the product manual, and check the product surface treatment and accessories.

（2）測量產品各部位基本尺寸，檢查門洞口是否與卷簾門尺寸相符，導軌、支架埋件位置、數量是否正確。

(2) Measure the basic dimensions of each part of the product, check whether the door opening is consistent with the size of the rolling shutter door, and whether the position and quantity of the embedded parts of the guide rail and bracket are correct.

（3）測量洞口標高，彈出兩導軌垂線及卷筒線。

(3) Measure the elevation of the hole and snap the vertical line of the two guide rails and the center line of the drum.

（4）將墊板電焊在預埋鐵板上，用螺絲固定卷筒的左右支架，安裝卷筒。卷筒安裝后應轉動靈活。

(4) Weld the base plate on the embedded iron plate, fix the left and right supports of the drum with screws, and install the drum. The drum shall rotate flexibly after installation.

（5）安裝減速器和傳動系統；安裳電氣拴街系統；空載試車。

(5) Install the reducer and transmission system; Anshang electric street system; No-load test run.

（6）先用手去試運行，再用電動機啟閉數次，調整無卡住、阻滯及異常。

(6) First, use your hand to test run, then start and close the motor several times, and adjust it to be free of jamming, blocking and abnormality.

卷簾門簾片穿好后，要將兩邊用封頭給封好，然后用拉鉚釘將其拉住，在一邊對簾子進行打孔一邊用繩拴住，接著在用鏍絲桿將簾子和軸緊密連在一起，后將卷簾門的簾子進行調平處理，以保證卷簾門使用的合理性。然后在將卷簾門來回的上升及下降，以檢測其的安裝質量及。更多相關的內容就來我們網站http://m.ifxf.cn咨詢！

After the roller shutter is put in place, both sides shall be sealed with heads, and then pulled with rivets. The curtain shall be punched at one side and tied with ropes. Then the curtain and shaft shall be tightly connected with screw rods, and then the curtain of the roller shutter shall be leveled to ensure the safety and rationality of the roller shutter. Then raise and lower the shutter door back and forth to check its installation quality and safety. Come to our website for more relevant content http://m.ifxf.cn consulting service