The use of electric roller shutter will cause some faults if it is used for a long time, so everyone must pay attention to the maintenance of some details in the maintenance time of Jinan roller shutter, because the roller shutter also needs maintenance, just like the car, it needs a period of time for maintenance and inspection, and see the relevant performance, Then how to keep it? Next, Jinan roller shutter manufacturer will give you a detailed explanation.

　　1.使用濟南卷簾門的過程,試圖保持控制器的穩定性和電壓,禁止安裝在非常潮濕的環境中,此外,不要打開遠程控制,如果發現門上身體繞線,結應當及時處理。注意通道是否堵塞，將門體堵下，若有不同反應立即停止電機運轉。

　　1. In the process of using Jinan roller shutter door, try to maintain the stability and voltage of the controller. It is forbidden to install it in a very humid environment. In addition, do not open the remote control. If the body on the door is found to be wound, the knot should be handled in time. Pay attention to whether the channel is blocked, block the door body, and stop the motor immediately in case of different reactions.

　　2.濟南卷簾門定期維護檢查電動百葉窗行程開關,上下如期控制器加上潤滑油,保持良好的操作,此外,操作員手動卷簾門,查看器的運行狀態,校對和行程開關位置,使電動門打開或關閉在適當?shù)奈恢?并在檢查的過程中打電動卷簾門頭部或底部或逆轉,如果出現緊急情況應立即停止轉動,切斷電源。

　　2. Jinan rolling shutter door shall be maintained and inspected regularly. The up and down controller shall be lubricated as scheduled to maintain good operation. In addition, the operator shall manually open or close the rolling shutter door and the operation status of the viewer, calibrate and stroke the switch position to make the opening or closing of the electric shutter in an appropriate position, and the head or bottom of the electric rolling shutter door shall be opened or reversed during the inspection, In case of emergency, stop rotating immediately and cut off the power supply.

　　3.操作者應定期檢查電動卷簾門的手動開關和手動升降裝飾，以防止電動卷簾門在緊急情況下會失靈，或造成不必要的事故。

　　3. The operator shall regularly check the manual switch and manual lifting decoration of the electric rolling shutter door to prevent the electric rolling shutter door from failure or unnecessary accidents in emergency.

　　4.軌道,明確電動百葉窗跟蹤,保持內部清潔,卷簾門電機和傳動鏈補充潤滑油,經常檢查控制裝置和開關控制盒,緊固連接端口,緊固螺絲,等,清潔表面控制箱,和按鈕上的灰塵污垢,防止按鈕堅持反彈。

　　4. Clear the track, clear the tracking of electric louver, keep the interior clean, add lubricating oil to the rolling shutter motor and transmission chain, frequently check the control device and switch control box, fasten the connection port, fasten the screw, etc., clean the dust and dirt on the surface control box and the button, and prevent the button from sticking to rebound.

　　以上就是我們濟南卷簾門廠家為您介紹關于“濟南卷簾門維修需要注意細節”,當然,我們把維護的核心部分,我們希望你可以結合知識的維護保養,以有效地保證卷簾門的使用壽命。如果您在這方面有任何問題，請及時與我們聯系，我們會及時為您解決。

　　The above is our Jinan roller shutter manufacturer's introduction to "Jinan roller shutter door maintenance needs to pay attention to details". Of course, we put the core part of the maintenance, we hope you can combine the maintenance of knowledge to effectively ensure the service life of the roller shutter door. If you have any problems in this area, please contact us in time and we will solve them for you in time.