在任何一個、酒店、大廈里隨處可見到防火門、防火窗、卷簾門等產品，那么你知道卷簾門的手控檢查與自控檢查是怎么樣的嗎？下面濟南卷簾門廠家為您分析：

"In any mall, hotel, or building, you can find fire doors, fire windows, roller shutter doors, and other products everywhere. Do you know how manual and automatic inspection of roller shutter doors works?"? Jinan roller shutter door manufacturer will analyze for you:

手控檢查：

Manual control inspection:

外觀檢查門軌、門扇有無變形、卡阻現象，手動按鈕是否良好上鎖。

Visually check whether the door rails and door leaves are deformed or jammed, and whether the manual buttons are properly locked.

查看卷簾門的電控箱指示訊號是否正常，箱體是否完好。

Check whether the indication signal of the electric control box of the roller shutter door is normal and whether the box is in good condition.

開啟按鈕箱門，按動向上（或向下）按鈕，卷簾門應上升（或下降）。

Open the button box door and press the up (or down) button to raise (or lower) the roller shutter door.

在按鈕操作上升（或下降）過程中，操作人員應密切注意卷簾門應上升（或下降）到端部位置時能否自動停車，若不能，應迅速手動停車，且必須待限位裝置修復（或調整）正常后方可重新操作。

During the process of button operation to raise (or lower), the operator should pay close attention to whether the roller shutter door can automatically stop when it should rise (or lower) to the end position. If not, it should be quickly and manually stopped, and it must be repaired (or adjusted) by the limit device before it can be operated again.

自控檢查：

Automatic control inspection:

用燃著的香煙等煙源使系統中任一煙感動作時，自動裝置將發出報警信號，同時自動啟動卷簾門電控系統兩次下滑關閉卷簾門。卷簾門一次下滑離地面1.2米左右停車，延時90秒左右，再自動啟動卷簾門全部關閉。

When using a burning cigarette or other smoke source to activate any smoke sensor in the system, the automatic device will send an alarm signal and automatically start the electric control system of the roller shutter door to slide down twice to close the roller shutter door. The rolling shutter door slides down to about 1.2 meters above the ground and stops, delaying about 90 seconds, and then automatically starts to close all the rolling shutter doors.

卷簾門關閉后，只有待煙感（或溫感）信號消失，或復位按鈕復位后方可重新開啟卷簾門。

After the roller shutter door is closed, it can only be reopened after the smoke (or temperature) signal disappears or the reset button is reset.

消防按鈕操作檢查：消防只設置卷簾門關閉按鈕，操作關閉按鈕卷簾門通過二次下滑關閉到位后，檢查消防信號指示是否正常。

Inspection of button operation in the fire control center: The fire control center is only equipped with a shutter door closing button. After the shutter door is closed in place through a second slide, check whether the signal indication in the fire control center is normal.

針對系統中檢查出來的缺陷及時修復。

Timely repair the defects detected in the system.

對優泰卷簾門進行清掃除塵，若有油漆脫落及局部變形的地方進行修復，確保卷簾門外觀清潔美觀。

Clean and dust the Youtai roller shutter door, and repair any paint peeling and local deformation to ensure a clean and beautiful appearance of the roller shutter door.

完成以上全部自檢項目，對卷簾門控制箱自檢按鈕、故障報警消聲鍵、復位鍵進行專門檢查。緊固各電線接頭、清潔控制箱內的灰塵，檢查箱內電氣元件是否齊備。還有什么相關事項就來我們網站http://m.ifxf.cn咨詢吧！

Complete all the above self-inspection items, and conduct special inspections on the self-inspection button, fault alarm silencing button, and reset button of the roller shutter control box. Fasten each wire connector, clean the dust inside the control box, and check whether the electrical components inside the box are complete. If there are any other related matters, please come to our website http://m.ifxf.cn Consult!